SANDPIPER Heavy-Duty Flap Valve AODD Pumps
SANDPIPER có giải pháp bơm cho chất lỏng chứa chất rắn có kích thước đường ống lên đến 3"/4".
Bơm van cánh chịu tải nặng SANDPIPER HDF3 và HDF4 có thiết kế đã được chứng minh có thể giải quyết những thách thức phổ biến nhất trong các ứng dụng bể chứa, thoát nước mỏ và bất kỳ ứng dụng chất lỏng nào liên quan đến chất rắn.
Bơm van cánh chịu tải nặng SANDPIPER HDF3 và HDF4 có thiết kế đã được chứng minh có thể giải quyết những thách thức phổ biến nhất trong các ứng dụng bể chứa, thoát nước mỏ và bất kỳ ứng dụng chất lỏng nào liên quan đến chất rắn.
Bơm màng đôi vận hành bằng khí (AODD) này được khuyến nghị sử dụng cho bùn mài mòn, chất rắn lơ lửng, không lơ lửng và chất rắn có kích thước đường ống lên đến 3"/4". Bơm van cánh chịu tải nặng được cấu hình với cổng xả dưới cùng để cung cấp lực hút vượt trội và ngăn chất rắn lắng đọng làm giảm tuổi thọ của bơm.
Được thiết kế cho các ứng dụng khó khăn và hiệu quả tối đa, bơm HDF3 và HDF4 có thành dày được chế tạo bằng nhôm đúc nguyên khối, gang hoặc thép không gỉ với màng chắn bằng chất đàn hồi và TPE (chất đàn hồi nhiệt dẻo) và van một chiều.
Thiết kế bơm HDF3 và HDF4 gần đây đã được tối ưu hóa về hiệu suất như một phần cải tiến trong danh mục SANDPIPER Evolution. Các bơm hiệu quả này đã tăng lưu lượng 19%, với lưu lượng tối đa mới lên tới 310 gpm (1.173 lpm).
Ưu điểm chính
- Xử lý chất rắn có kích thước lớn - Bơm van cánh so với bơm van bi
- Bơm van kiểm tra cánh: Diện tích lưu lượng lớn cho phép chất rắn có kích thước đường ống lên tới 3"/4" đi trực tiếp qua bơm. Ngoài ra, cổng xả dưới cùng cho phép chất rắn lắng đi qua bơm và không lắng bên trong buồng bơm, ngăn ngừa hư hỏng và mài mòn sớm.
- Bơm van kiểm tra bi: Diện tích lưu lượng nhỏ hơn nhiều để chất rắn đi qua. Chất rắn lớn bị kẹt trong ống hút và chất rắn nhỏ có thể lắng trong buồng ngoài - cả hai vấn đề đều ảnh hưởng đến hiệu suất bơm.
- Lực nâng hút vượt trội - Bơm van cánh so với bơm van bi
- Ưu điểm lực nâng hút: Thiết kế van cánh của SANDPIPER cung cấp khả năng nâng hút vượt trội lên đến 24 ft trong nước. Vị trí màng ngăn và chỗ ngồi van cánh kết hợp để tạo ra một đơn vị có khả năng nâng lực hút lớn hơn 15% so với bơm van bi.
- Hút khô: Những khả năng này đến từ hút khô, khiến bơm van cánh SANDPIPER trở thành giải pháp tuyệt vời cho những tình huống có ít lựa chọn mồi bơm.
HDF3-A & HDF4-A HEAVY DUTY FLAP VALVE PUMP
TECHNICAL DATA SHEETS
TECHNICAL DATA SHEETS
HEAVY DUTY FLAP VALVE PUMP
For fluids containing up to line sized solids
SUCTION / DISCHARGE PORT SIZE
PUMP SERIES
- 3” 150# ANSI Flange
- 0 to 310 gallons per minute (0 to 1173 LPM)
- No-lube, no-stall design
- Up to nearly 3” (75mm)
- 125 psi or 289 ft. of water (8.8 Kg/cm2 or 88 meters)
- 125 psi (8.6 bar)
- 1.60 Gallon / 6.08 liter
- HDF3A: 345 lbs (151kg)
- HDF4A: 415 lbs (182kg)
5 YEAR LIMITED PRODUCT WARRANTY
5 Year Guarantee for defects in material or workmanship. See sandpiperpump.com/content/warranty-certifications for complete warranty, including terms and conditions, limitations and exclusions.
5 Year Guarantee for defects in material or workmanship. See sandpiperpump.com/content/warranty-certifications for complete warranty, including terms and conditions, limitations and exclusions.
USE ONLY GENUINE SANDPIPER PARTS
All certification, standards, guarantees & warranties originally supplied with this pump will be invalidated by the use of service parts not identified as “Genuine SANDPIPER Parts.”
All certification, standards, guarantees & warranties originally supplied with this pump will be invalidated by the use of service parts not identified as “Genuine SANDPIPER Parts.”
EXPLANATION OF PUMP NOMENCLATURE
PUMP SERIES
- H D Heavy Duty
- F Flap
- 3 3” 150# ANSI
Style Flange
- 4 4” 150# ANSI Style Flange
- D Bottom (Top Suction-Buttom Discharge)
- A Neoprene/Urethane
- B Nitrile
- K Neoprene/Hytrel
- N Neoprene
- S Santoprene
DESIGN LEVEL 7 (3” pump)
- 3 (4” pump)
- A Aluminum Wetted, Aluminum Air
MATERIALS
CONDUCTIVE ACETAL: Tough, impact resistant, ductile. Good abrasion resistance and low friction surface. Generally inert, with good chemical resistance except for strong acids and oxidizing agents.
EPDM: Shows very good water and chemical resistance. Has poor resistance to oils and solvents, but is fair in ketones and alcohols.
FKM (FLUOROCARBON): Shows good resistance to a wide range of oils and solvents; especially all aliphatic, aromatic and halogenated hydrocarbons, acids, animal and vegetable oils. Hot water or hot aqueous solutions (over 70°F(21°C)) will attack FKM.
HYTREL®: Good on acids, bases, amines and glycols at room temperatures only.
NEOPRENE: All purpose. Resistance to vegetable oils. Generally not affected by moderate chemicals, fats, greases and many oils and solvents. Generally attacked by strong oxidizing acids, ketones, esters and nitro hydrocarbons and chlorinated aromatic hydrocarbons.
NITRILE: General purpose, oil-resistant. Shows good solvent, oil, water and hydraulic fluid resistance. Should not be used with highly polar solvents like acetone and MEK, ozone, chlorinated hydrocarbons and nitro hydrocarbons.
NYLON: 6/6 High strength and toughness over a wide temperature range. Moderate to good resistance to fuels, oils and chemicals.
POLYPROPYLENE: A thermoplastic polymer. Moderate tensile and flex strength. Resists stong acids and alkali. Attacked by chlorine, fuming nitric acid and other strong oxidizing agents.
PVDF: (Polyvinylidene Fluoride) A durable fluoroplastic with excellent chemical resistance. Excellent for UV applications. High tensile strength and impact resistance.
SANTOPRENE®: Injection molded thermoplastic elastomer with no fabric layer. Long mechanical flex life. Excellent abrasion resistance.
UHMW PE: A thermoplastic that is highly resistant to a broad range of chemicals. Exhibits outstanding abrasion and impact resistance, along with environmental stress-cracking resistance.
URETHANE: Shows good resistance to abrasives. Has poor resistance to most solvents and oils.
VIRGIN PTFE: (PFA/TFE) Chemically inert, virtually impervious. Very few chemicals are known to chemically react with PTFE; molten alkali metals, turbulent liquid or gaseous fluorine and a few fluoro-chemicals such as chlorine trifluoride or oxygen difluoride which readily liberate free fluorine at elevated temperatures.
Maximum and Minimum Temperatures are the limits for which these materials can be operated. Temperatures coupled with pressure affect the longevity of diaphragm pump components. Maximum life should not be expected at the extreme limits of the temperature ranges.
ALLOY C: Equal to ASTM494 CW-12M-1 specification for nickel and nickel alloy.
STAINLESS STEEL: Equal to or exceeding ASTM specification A743 CF-8M for corrosion resistant iron chromium, iron chromium nickel and nickel based alloy castings for general applications. Commonly referred to as 316 Stainless Steel in the pump industry.